Hepco Becker pannier latch replaced

Aprilia Caponord ETV1000 Rally-Raid Hepco Becker 700101 00 01 pannier latchJust got around to fixing my ‘breakdown’ – the new latch (Hepco Becker Part No: 700101 00 01) arrived today and after a hearty breakfast I set about changing out the broken one. The kit is a ‘universal’ one for all HB panniers and so a whole bunch of the bits supplied are immediately resigned to the waste bin …….. I’d have been happier with just the latch and a few quid off to be honest!

So out with the foam liner, off with the bottle rack and remove the five countersunk Aprilia Caponord ETV1000 Rally-Raid Hepco Becker 700101 00 01 pannier latchbolts/washers/nuts and pull the aluminium box away from the frame. Next, drill the heads off the four solid rivets using a drill bit approx 6mm or slightly larger. Then lever the old latch away and separate it from the spacer. Job done …… now for the rebuild!

The latch as supplied comes with 3mm rivets and is drilled to suit, unfortunately the Alu Exclusive luggage was  put together with 4mm solid rivets because of clearance between frame and case. No worries, down to the hardware store and a bag of 4mm Dia 10mm long stainless rivets are on hand to do the business. Once in, the heads are ground down a smidgen with the Dremel to achieve the same clearance without compromising shear strength.

Aprilia Caponord ETV1000 Rally-Raid Hepco Becker 700101 00 01 pannier latchRebuild is a straight reversal of strip-down, but  everything gets a thorough clean, grease and general pampering to make it feel good. The pannier is now solid once again and if I get 13 years out of this lock and rivets like the last set, I’ll be a happy bunny.

Thanks go to Griff at hepco-and-becker-luggage.co.uk (web face of moto bins) who chased up key numbers with me and made sure the latch was on the doorstep in Oxford the next day – excellent service.

 

First ‘breakdown’ in ages

Aprilia Caponord ETV1000 Rally-Raid broken Hepco Becker Alu Exclusive pannier latchRemoved the right pannier the other day while changing out the rear brake pads (makes life a bit easier!) but couldn’t get the latch to close properly when refitting it …… turns out the latch has broken on one side of the pivot. It looks like it’s just fatigue over the years of bouncing (over) loaded boxes across the continent. So a new latch (Hepco Becker part no: 700.101.00.01) has been ordered from http://www.hepco-and-becker-luggage.co.uk a spin-off company of Moto-Bins. Cost should be £22.80 but they’re knocking 15% off at the moment, so it cost £19.38 delivered. I can live with that!

The latch comes complete with new lock, keys and pop-rivets to fit it. However the original is installed with solid rivets, so this is what I’ll use as well. This of course means stripping the liner out and unbolting the aluminium box from the chrome/steel frame, but it’s only a 10-15 minute job and a good excuse to give everything a damn good clean and polish at the same time. 😀

Brew ha-ha!

I’ve written before about the good and bad points of the Aprilia (Rimowa) panniers, but one of the niggles I never mentioned was the carry handle on the lid. I never use it and the damn thing gets in the way.

So after a happy couple of hours cutting, sanding and drilling … they’ve been replaced by a nice piece of checker plate. A vast expanse of flat surface on which to make a brew and sort out my sarnies and nibbles. Smashing stuff!

Now I’m looking for a set of ‘pannier-top’ bags to finish off the job … bags to put the afore mentioned sarnies and tea brewing paraphernalia into. No more unstrapping panniers to delve inside for munchy stuff, it’ll all be on hand at the ‘zzzz‘ of a zip ….

Thinking inside the box

Aprilia Caponord ETV1000 Rally-Raid - arti-farty pic!The Rally Raid comes as standard with luggage – Aprilia badged Hepco & Becker ‘Alu-Exclusive’ luggage to be exact. And pretty good it is too … if a little wide. Each of the panniers – from Aprilia £421.02 each (unbadged – £317.25 each) holds a quoted 41L but in fact holds nearer 28L once you take into account the room lost to the foam lining. In fact that lining is one of the case’s endearing features. It not only provides added rigidity to the case, but also makes it very thermally efficient – excellent for keeping stuff cool on long hot ride-outs.Aprilia Caponord ETV1000 Rally-Raid Hepco Becker Alu Exclusive hinge

The lid hinges forward about 120° to a stop – a nice touch that prevents the lids dropping down against the pannier body and stressing the hinge. A single locking latch keeps the lid locked tight against the weather seal which, though not completely waterproof does a damn good job (rain for 1,500 miles/24hrs and only let in an egg-cup full).

So far so good … but now the not so nice bits. Firstly, the pannier is only held in place by one latch. A latch that can be easily broken in a low-speed ‘off’, leaving the pannier to fall away to its lonesome fate bouncing down the carriageway. Secondly, fitting water bottle frames etc. That foam liner now becomes a pain .. you either have to remove it, or drill it Aprilia Caponord ETV1000 Rally-Raid Hepco Becker Alu Exclusive hingeto fit screws/bolts through . I used a tool that takes a 10mm ‘core’ out, then re-glued it into place – neat, but fiddly. Lastly, the rigidity the foam provides – it’s deliberate . As the aluminium body is thin, VERY thin .. like 0.5mm thin, it needs the foam to hold its shape. That means that in a spill the cases deform alarmingly easily as the aluminium has no strength of its own – not good at all.

This all leads to the question of upgrading the pannier system. I want to use the original frames and just replace the boxes. I don’t want to compromise on space or water-resistance, but I do want to improve on pannier strength – albeit at a slight weight gain. I want boxes that only scuff, not crush like a bag of crisps when the bike drops on its side …. and are relatively burst-proof when faced with a BIG impact – sadly, the Hepco-Becker has neither of these virtues.

Here are the systems I’ve looked at:-

Hepco & Becker – straight swap, different models but mass produced to a budget. Up to approx. £550 per pair.

Touratech – Easy to fit with provided kit but expensive and living off their name. Up to approx. £600 per pair.

Caja Sahel – Hand made and easy to fit with Touratech mounts. Powder coated with tie-down points provided. €450-550 per pair.

Project VND – Hand made and easy to fit with Touratech mounts. Anodised finish with hinged and removable lid. £500-600 per pair.

Metal Mule – Nice, but expensive and needs dedicated mounting system. System from £1,300!

Aprilia Caponord ETV1000 Rally-Raid - CAD panniersOr the other option … design and build your own! Well almost. I’m happy to do the designing bit, but manufacturing is a tad more complex, at least to get a ‘factory’ finish …. and frankly, my aluminium welding leaves more holes than welds. So I’ve enlisted the help of a local metal guru to turn my drawings into reality … and when finished, they’ll look something like this.

500mm Long x 430mm Tall x 250mm Wide (using 2mm aluminium) ….. so the same width as the originals but longer and taller, giving a (hopefully) usable volume somewhere around 47L each. They’ll be mounted to the existing 15mm dia. rails with Touratech mount kits (01-053-0010-0 approx. €47).